|
76MMOD X 54MM 316L Pressfit Reducing Tee
TFPFRT607654
In Stock
|
|
Anzor Pressfit Fittings - Certified by Bureau Veritas Marine & Offshore International Register
Use the guide below to check media compatibility across 316L stainless steel and common sealing materials. For application-specific entries, always consider the stated diameter, pressure and operating conditions.
| Media / Fluid | Diameter (mm) |
Max Work Pressure (bar) |
316L | EPDM | HNBR | FKM / FPM | Notes / Conditions |
|---|---|---|---|---|---|---|---|
| Acetic acid 20% | — | — | |||||
| Acetone 100% | — | — | |||||
| Acetylene | <22 | 1.5 | — | AS4289 (15-35mm) | |||
| 28 | 1.3 | ||||||
| 35 | 1.0 | ||||||
| Ad Blue/Urea | 15-54 | 25 | — | — | |||
| 76-168 | 16 | ||||||
| Ammonia | 15-108 | 16 | — | Dry; max purity N3.8 | |||
| Ammonia dry | — | — | |||||
| Ammonium chloride 1% | — | — | |||||
| Ammonium nitrate 10+50% | — | — | |||||
| Ammonium phosphate 10% | — | — | |||||
| Ammonium sulfate 10% | — | — | |||||
| Aniline | — | — | |||||
| Aqua regia, aqua fortis | — | — | |||||
| Argon | 15-108 | 16 | — | Max purity N40 | |||
| Avgas | 15-54 | 25 | — | — | |||
| 76-168 | 16 | ||||||
| Battery acid | — | — | |||||
| Benzene | — | — | |||||
| Bio-Diesel (dry) (B100) | 15-54 | 25 | — | No water or wetting agents | |||
| 76-168 | 16 | ||||||
| Bio-Ethanol | 15-54 | 25 | — | E85 (85% Ethanol) | |||
| 76-168 | 16 | ||||||
| Bio-Gas | 15-168 | 16 | — | Methane, CO₂, nitrogen & hydrogen sulphide | |||
| Boric acid 5% | — | — | |||||
| Butane | 15-108 | 5 | — | — | |||
| Butanol | — | — | |||||
| Calcium Hydroxide ≤ 10°C | — | — | |||||
| Calcium Hypochlorite | — | — | |||||
| Carbon dioxide | 15-108 | 16 | — | Dry; max purity N2.5 | |||
| Carbon monoxide | 15-108 | 16 | — | Dry; max purity N3.7 | |||
| Caustic soda ≤ 50% | — | — | |||||
| Chlorine (dry) | — | — | |||||
| Citric acid 5% | — | — | |||||
| Compressed Air | 15-54 | 25 | — | If dry system | If wet system | If wet system | Dry <1.0 mg/m³ / wet (oil) lubricated air |
| 76-108 | 16 | ||||||
| Compressed air \* | — | — | |||||
| Copper chloride | — | — | |||||
| Copper nitrate | — | — | |||||
| Copper sulfate 10% | — | — | |||||
| Demineralised & RO Waters | 15-108 | 25 | — | — | — | Conductivity >0.1 µS/cm (EC), pH 4-14 | |
| 168 | 16 | ||||||
| Diesel | 15-54 | 25 | — | Flashpoint 50-80°C | |||
| 76-168 | 16 | ||||||
| Engine oil | — | — | |||||
| Ethane | 15-168 | 5 | — | — | |||
| Ethanol | 15-54 | 25 | — | Temp <+25°C | |||
| 76-168 | 16 | ||||||
| Ethylene glycol | — | — | |||||
| Ethylene Oxide | — | — | |||||
| Ferric chloride, watery | — | — | |||||
| Ferric sulfate | — | — | |||||
| Fire Services | 15-168 | 25 (refer ActivFire) | — | — | — | Sprinkler & hydrant | |
| Formaldehyde | — | — | |||||
| Formic acid | — | — | |||||
| Gas oil | — | — | |||||
| Gasoline | — | — | |||||
| Gear oil | — | — | |||||
| Glycol (<90% by vol) | 15-108 | 25 | — | EPDM for ethylene & propylene bases | |||
| 168 | 16 | ||||||
| Helium | 15-108 | 16 | — | Max purity N4.0 | |||
| Hexane | — | — | |||||
| Hydrochloric acid 100% | — | — | |||||
| Hydrogen | 15-108 | 16 | — | Max purity N4.0; may leak <0.001 cm³/min | |||
| Hydrogen fluoride | — | — | |||||
| Hydrogen peroxide 10% | — | — | |||||
| Kerosene | 15-54 | 25 | — | — | |||
| 76-168 | 16 | ||||||
| Linseed oil | — | — | |||||
| LPG (Propane) | 15-168 | 2(5) | — | AS 3688 approved; fitting marked "GAS" | |||
| Lubricants | — | — | — | — | — | ||
| Lubricating oils | — | — | |||||
| Machine oil | — | — | |||||
| Magnesium chloride ≤20% | — | — | |||||
| Magnesium hydroxide 100°C | — | — | |||||
| Magnesium sulfate <40% | — | — | |||||
| Methane | 15-108 | 5 | — | — | |||
| Methanol | 15-168 | 16 | — | — | |||
| Mineral oil | — | — | |||||
| Motor (Mineral) Oil, SAE | 15-54 | 25 | — | — | Not including E10 fuel with ethanol additives | ||
| 76-168 | 16 | ||||||
| Naphtha | — | — | |||||
| Naphthalene | — | — | |||||
| Nickel chloride 10÷30% | — | — | |||||
| Nickel sulfate | — | — | |||||
| Nitric acid ≤20% | — | — | |||||
| Paraffin | — | — | |||||
| Phosphoric acid | — | — | |||||
| Photo developer/fixing bath | — | — | |||||
| Potassium chloride | — | — | |||||
| Potassium hydroxide ≤ 50°C | — | — | |||||
| Potassium sulfate 10% | — | — | |||||
| Propane (liquefied) | — | — | |||||
| Propylene glycol (<90% by vol) | 15-108 | 25 | EPDM for ethylene & propylene bases | ||||
| 168 | 16 | ||||||
| Prussic acid | — | — | |||||
| Sea water | — | — | |||||
| Sodium bicarbonate | — | — | |||||
| Sodium chloride 5% | — | — | |||||
| Sodium nitrate ≤ 40% | — | — | |||||
| Sodium phosphate | — | — | |||||
| Sodium sulfate 10% | — | — | |||||
| Sulfuric acid 10% 60°C | — | — | |||||
| Sulfuric acid 100%, moist | — | — | |||||
| Sulfuric acid, smoking | — | — | |||||
| Sulphur dioxide (dry) | — | — | |||||
| Tannin | — | — | |||||
| Tanning agents for leather | — | — | |||||
| Tartaric Acid 10% 100°C | — | — | |||||
| Toluol 20°C | — | — | |||||
| Trichloroethylene | — | — | |||||
| Turpentine | — | — | |||||
| Water ≤ 100°C | — | — | |||||
| Water, deionised | — | — | |||||
| Water, distilled | — | — | |||||
| Zinc chloride | — | — | |||||
| Zinc sulfate 10% | — | — |
Guide only:This information is a guide only. Product selection and installation are the customer’s responsibility. Anzor accepts no liability for the application of this information. Suitability can vary with concentration, temperature, pressure and operating conditions. Where an application-specific rating is provided, use those stated conditions rather than the general compatibility rating.
|
76MMOD X 54MM 316L Pressfit Reducing Tee
TFPFRT607654
In Stock
|
|
Anzor Pressfit Fittings - Certified by Bureau Veritas Marine & Offshore International Register
Use the guide below to check media compatibility across 316L stainless steel and common sealing materials. For application-specific entries, always consider the stated diameter, pressure and operating conditions.
| Media / Fluid | Diameter (mm) |
Max Work Pressure (bar) |
316L | EPDM | HNBR | FKM / FPM | Notes / Conditions |
|---|---|---|---|---|---|---|---|
| Acetic acid 20% | — | — | |||||
| Acetone 100% | — | — | |||||
| Acetylene | <22 | 1.5 | — | AS4289 (15-35mm) | |||
| 28 | 1.3 | ||||||
| 35 | 1.0 | ||||||
| Ad Blue/Urea | 15-54 | 25 | — | — | |||
| 76-168 | 16 | ||||||
| Ammonia | 15-108 | 16 | — | Dry; max purity N3.8 | |||
| Ammonia dry | — | — | |||||
| Ammonium chloride 1% | — | — | |||||
| Ammonium nitrate 10+50% | — | — | |||||
| Ammonium phosphate 10% | — | — | |||||
| Ammonium sulfate 10% | — | — | |||||
| Aniline | — | — | |||||
| Aqua regia, aqua fortis | — | — | |||||
| Argon | 15-108 | 16 | — | Max purity N40 | |||
| Avgas | 15-54 | 25 | — | — | |||
| 76-168 | 16 | ||||||
| Battery acid | — | — | |||||
| Benzene | — | — | |||||
| Bio-Diesel (dry) (B100) | 15-54 | 25 | — | No water or wetting agents | |||
| 76-168 | 16 | ||||||
| Bio-Ethanol | 15-54 | 25 | — | E85 (85% Ethanol) | |||
| 76-168 | 16 | ||||||
| Bio-Gas | 15-168 | 16 | — | Methane, CO₂, nitrogen & hydrogen sulphide | |||
| Boric acid 5% | — | — | |||||
| Butane | 15-108 | 5 | — | — | |||
| Butanol | — | — | |||||
| Calcium Hydroxide ≤ 10°C | — | — | |||||
| Calcium Hypochlorite | — | — | |||||
| Carbon dioxide | 15-108 | 16 | — | Dry; max purity N2.5 | |||
| Carbon monoxide | 15-108 | 16 | — | Dry; max purity N3.7 | |||
| Caustic soda ≤ 50% | — | — | |||||
| Chlorine (dry) | — | — | |||||
| Citric acid 5% | — | — | |||||
| Compressed Air | 15-54 | 25 | — | If dry system | If wet system | If wet system | Dry <1.0 mg/m³ / wet (oil) lubricated air |
| 76-108 | 16 | ||||||
| Compressed air \* | — | — | |||||
| Copper chloride | — | — | |||||
| Copper nitrate | — | — | |||||
| Copper sulfate 10% | — | — | |||||
| Demineralised & RO Waters | 15-108 | 25 | — | — | — | Conductivity >0.1 µS/cm (EC), pH 4-14 | |
| 168 | 16 | ||||||
| Diesel | 15-54 | 25 | — | Flashpoint 50-80°C | |||
| 76-168 | 16 | ||||||
| Engine oil | — | — | |||||
| Ethane | 15-168 | 5 | — | — | |||
| Ethanol | 15-54 | 25 | — | Temp <+25°C | |||
| 76-168 | 16 | ||||||
| Ethylene glycol | — | — | |||||
| Ethylene Oxide | — | — | |||||
| Ferric chloride, watery | — | — | |||||
| Ferric sulfate | — | — | |||||
| Fire Services | 15-168 | 25 (refer ActivFire) | — | — | — | Sprinkler & hydrant | |
| Formaldehyde | — | — | |||||
| Formic acid | — | — | |||||
| Gas oil | — | — | |||||
| Gasoline | — | — | |||||
| Gear oil | — | — | |||||
| Glycol (<90% by vol) | 15-108 | 25 | — | EPDM for ethylene & propylene bases | |||
| 168 | 16 | ||||||
| Helium | 15-108 | 16 | — | Max purity N4.0 | |||
| Hexane | — | — | |||||
| Hydrochloric acid 100% | — | — | |||||
| Hydrogen | 15-108 | 16 | — | Max purity N4.0; may leak <0.001 cm³/min | |||
| Hydrogen fluoride | — | — | |||||
| Hydrogen peroxide 10% | — | — | |||||
| Kerosene | 15-54 | 25 | — | — | |||
| 76-168 | 16 | ||||||
| Linseed oil | — | — | |||||
| LPG (Propane) | 15-168 | 2(5) | — | AS 3688 approved; fitting marked "GAS" | |||
| Lubricants | — | — | — | — | — | ||
| Lubricating oils | — | — | |||||
| Machine oil | — | — | |||||
| Magnesium chloride ≤20% | — | — | |||||
| Magnesium hydroxide 100°C | — | — | |||||
| Magnesium sulfate <40% | — | — | |||||
| Methane | 15-108 | 5 | — | — | |||
| Methanol | 15-168 | 16 | — | — | |||
| Mineral oil | — | — | |||||
| Motor (Mineral) Oil, SAE | 15-54 | 25 | — | — | Not including E10 fuel with ethanol additives | ||
| 76-168 | 16 | ||||||
| Naphtha | — | — | |||||
| Naphthalene | — | — | |||||
| Nickel chloride 10÷30% | — | — | |||||
| Nickel sulfate | — | — | |||||
| Nitric acid ≤20% | — | — | |||||
| Paraffin | — | — | |||||
| Phosphoric acid | — | — | |||||
| Photo developer/fixing bath | — | — | |||||
| Potassium chloride | — | — | |||||
| Potassium hydroxide ≤ 50°C | — | — | |||||
| Potassium sulfate 10% | — | — | |||||
| Propane (liquefied) | — | — | |||||
| Propylene glycol (<90% by vol) | 15-108 | 25 | EPDM for ethylene & propylene bases | ||||
| 168 | 16 | ||||||
| Prussic acid | — | — | |||||
| Sea water | — | — | |||||
| Sodium bicarbonate | — | — | |||||
| Sodium chloride 5% | — | — | |||||
| Sodium nitrate ≤ 40% | — | — | |||||
| Sodium phosphate | — | — | |||||
| Sodium sulfate 10% | — | — | |||||
| Sulfuric acid 10% 60°C | — | — | |||||
| Sulfuric acid 100%, moist | — | — | |||||
| Sulfuric acid, smoking | — | — | |||||
| Sulphur dioxide (dry) | — | — | |||||
| Tannin | — | — | |||||
| Tanning agents for leather | — | — | |||||
| Tartaric Acid 10% 100°C | — | — | |||||
| Toluol 20°C | — | — | |||||
| Trichloroethylene | — | — | |||||
| Turpentine | — | — | |||||
| Water ≤ 100°C | — | — | |||||
| Water, deionised | — | — | |||||
| Water, distilled | — | — | |||||
| Zinc chloride | — | — | |||||
| Zinc sulfate 10% | — | — |
Guide only:This information is a guide only. Product selection and installation are the customer’s responsibility. Anzor accepts no liability for the application of this information. Suitability can vary with concentration, temperature, pressure and operating conditions. Where an application-specific rating is provided, use those stated conditions rather than the general compatibility rating.
Build faster and stronger decks with S2 Decking Screws.
To be the best, speed matters.
Build your deck with Anzor's Stainless Steel Decking Screws
AM Ruspert Concrete Screws: More Fixing Options with Multiple Embedment Depths
To receive useful info and product updates add your details below
Request a copy of our Engineering & Marine, or Construction Wall Chart.
Click here to download a PDF of our Engineering Catalogue. This catalogue includes stainless fasteners and fittings, marine hardware and construction brackets.
Click here to download a PDF of our Construction Catalogue. This catalogue includes stainless/galvanized fasteners and fittings, and construction brackets.
