12 X 86 Fischer FBN II 12/5 HDG Anchor Bolt 508014

Home
/ Concrete Anchors
/ Fischer FBN II Bolt Anchor
/ Hot Dip Galvanised
/ 12 X 86 Fischer FBN II 12/5 HDG Anchor Bolt 508014

12 X 86 Fischer FBN II 12/5 HDG Anchor Bolt 508014

DYTMG1205FBN

In Stock

12 X 86 Fischer FBN II 12/5 HDG Anchor Bolt 508014

DYTMG1205FBN

In Stock

The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.

Advantages

FBN II Bolt Anchors have ETA (European technical assessment) that meets the NZBC requirements (NZS 3101 concrete structures standard)
For external use with 50 Year Design Life when used as described in ETA
Meets BPIR regulation
With assessment document (ETA) the hot dipped galvanised steel version is covered for external use with variable working life depending on environment and corrosion conditions.
The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
Simple assembly due to few taps and minimal slippage.

Applications and Approval

Applications

Steel constructions
Guard rails
Consoles
Ladders
Machines
Gates
Façades

Building materials

Approved for:

Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

Concrete C12/15
Natural stone with dense structure

You can find detailed information on building materials in the approval document.

Approval

ETA-07/0211
ETA-18/0101
DoP No. 0098
DoP No. 0268

Installation

Functionality

The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions.
Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut).
When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall.
The head embossing offers a simple control of the anchoring.
In the case of series installation, we recommend using the FABS bolt anchor setting tool.
Visit fischer for Technical Data and Assembly Instructions.

Declaration of Performance (Mechanical Anchor for use in concrete)

Fischer Free Design Software

12 X 86 Fischer FBN II 12/5 HDG Anchor Bolt 508014

DYTMG1205FBN

In Stock

12 X 86 Fischer FBN II 12/5 HDG Anchor Bolt 508014

DYTMG1205FBN

In Stock

Advantages

FBN II Bolt Anchors have ETA (European technical assessment) that meets the NZBC requirements (NZS 3101 concrete structures standard)
For external use with 50 Year Design Life when used as described in ETA
Meets BPIR regulation
With assessment document (ETA) the hot dipped galvanised steel version is covered for external use with variable working life depending on environment and corrosion conditions.
The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
Simple assembly due to few taps and minimal slippage.

Applications and Approval

Applications

Steel constructions
Guard rails
Consoles
Ladders
Machines
Gates
Façades

Building materials

Approved for:

Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

Concrete C12/15
Natural stone with dense structure

You can find detailed information on building materials in the approval document.

Approval

ETA-07/0211
ETA-18/0101
DoP No. 0098
DoP No. 0268

Installation

Functionality

The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions.
Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut).
When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall.
The head embossing offers a simple control of the anchoring.
In the case of series installation, we recommend using the FABS bolt anchor setting tool.
Visit fischer for Technical Data and Assembly Instructions.

Downloads

ETA - Concrete

Load Table

Technical Data Sheet

Declaration of Performance (Mechanical Anchor for use in concrete)

Fischer Free Design Software